Manufacture and mechanical characterization of composite material of carbon fiber with matrix of PEEK
DOI:
https://doi.org/10.22517/23447214.24826Keywords:
Carbon Fiber, Epoxy Resin, Manufacture, PEEK, Mechanical Characterization, ThreadAbstract
In this study, a low-cost simple manufacturing process for a composite material of thermoplastic matrix PolyEtherEtherKetone (PEEK) and carbon fiber (CF) was developed. The composite material CF/PEEK was mechanically evaluated by three-point bending and tension tests, obtaining the elastic modulus and the maximum tensile stress respectively. Also, threads were made in the composite material and the strength of threads machined on the composite material was evaluated with tension tests. A comparison of the composite material CF/PEEK and the composite material of carbon fiber and epoxy resin (CF/EP) was performed, the elastic modules, peak tensile stresses and the strength of threads were compared. It was found that it was possible to produce the CF/PEEK composite at low cost by hot molding. The elastic modulus and tensile strength of the CF/PEEK were lower than those obtained in the CF/EP. However, the performance of the thread in tension was better for CF/PEEK compared to CF/EP.
Downloads
References
[1] C. Soutis, "Fibre reinforced composites in aircraft construction," Prog. Aerosp. Sci., vol. 41, no. 2, pp. 143-151, 2005, DOI: https://doi.org/10.1016/j.paerosci.2005.02.004
[2] A. Imad Shakir, O. Sief aldeen, H. Kamalaldin F. and J. Mohammed A., "Properties evaluation of fiber reinforced polymers and their constituent materials used in structures - A review," Mater. Today, vol. 43, p. 1003-1008, 2021, DOI: https://doi.org/10.1016/j.matpr.2020.07.636
[3] P. Mallick, "Fiber-reinforced composites materials," in Manufacturing and design, 3rd ed., vol. 20, 1989, pp. 172-173. DOI: https://doi.org/10.1016/0010-4361(89)90651-4
[4] T. J. Hoskins, K. D. Dearn and S. N. Kukureka, "Mechanical performance of PEEK produced by additive manufacturing," Polym. Test, vol. 70, pp. 511-519, 2018. DOI: https://doi.org/10.1016/j.polymertesting.2018.08.008
[5] S. Baeten and I. Verpoest, "Optimisation of a GMT-based cold pressing technique for low cost textile reinforced thermoplastic composites," Compos Part A-Appl S, no. 30, p. 667-682, 1999. DOI: https://doi.org/10.1016/S1359-835X(98)00173-0
[6] N. Nier, E. Päßler, J. Weißhuhn, K. Roder, D. Nestler, L. Kroll, S. Spange and G. Wagner, "Evaluation of the molding process for production of short-fibre-reinforced C/C-SiC composites," J. Eur. Ceram. Soc., no. 40, p. 1057-1066, 2020. DOI: https://doi.org/10.1016/j.procir.2019.10.004
[7] S. Guangyong, K. Xiangren, W. Zhen, L. Quantian and L. Qing, "Experimental investigation into stamping of woven CF/PP laminates: Influences of molding temperature on thermal, mesoscopic and macroscopic properties," Compos. Struct., no. 263, 2021. DOI: https://doi.org/10.1016/j.compstruct.2020.113507
[8] D. M. Wirth and J. K. Pokorski, "Design and fabrication of a low-cost pilot-scale melt-processing system," Polymer, no. 181, 2019. DOI: https://doi.org/10.1016/j.polymer.2019.121802
[9] H. Chao and Q. Qing-Hua, "Advances in fused deposition modeling of discontinuous fiber/polymer composites," Curr Opin Solid State Mater Sci., no. 24, 2020. DOI: https://doi.org/10.1016/j.cossms.2020.100867
[10] K. Palanikumar, M. Mudhukrishnan and P. Soorya Prabha, "Technologies in additive manufacturing for fiber reinforced composite materials: a review," Curr. Opin. Chem. Eng., no. 28, p. 51-59, 2020. DOI: https://doi.org/10.1016/j.coche.2020.01.001
[11] N. Fuda, C. Weilong, Q. Jingjing, W. Junhua and W. Shiren, "Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling," Compos. B. Eng., no. 80, pp. 369-378, 2015. DOI: https://doi.org/10.1177/0021998316646169
[12] G. A. Ramadhani, S. Susmartini, L. Herdiman, I. Priadythama and D. Shepherd, "Advanced composite-based material selection for prosthetic socket application in developing countries," Cogent Eng., no. 7, 2020. DOI: https://doi.org/10.1080/23311916.2020.1745553
[13] A. Sazrhi, R. O. Bura and G. Amperiawan, "Mastery of Composite Materials to Support Indonesia's Defense Industry," IEEE 6th Asian Conference on Defense Technology (ACDT), pp. 13-15, 2019. DOI: https://doi.org/10.1109/ACDT47198.2019.9072849
[14] K. Ghavami and A. Azadeh, "Nonconventional materials (NOCMAT) for ecological and sustainable development," MRS Adv., vol. 1, no. 53, pp. 3553-3563, 2016. DOI: https://doi.org/10.1557/adv.2016.613
[15] T. Suoware, S. Onyemaechi, B. Ugwu and E. Amula, "Development of flame retarded composite fibreboard for building applications using oil palm residue," Materiales de Construcción, vol. 69, no. 335, 2019. DOI: https://doi.org/10.3989/mc.2019.10418
[16] M. Ramesh, T. S. A. Atreya, U.S. Aswin, H. Eashwar and C. Deepa, "Processing and mechanical property evaluation of banana fiber reinforced polymer composites," Procedia Eng., vol. 97, pp. 563-572, 2014. DOI: https://doi.org/10.1016/j.proeng.2014.12.284
[17] A. Majid, "Use of coconut fibre reinforced concrete and coconut-fibre ropes for seismic-resistant construction," Materiales de Construcción, vol. 66, no. 321, 2016. DOI: https://doi.org/10.3989/mc.2016.01015
[18] N. Batista, P. Olivier, G. Bernhart, M. Rezende and E. Botelho, "Correlation between degree of crystallinity, morphology and mechanical properties of PPS/carbon fiber laminates", Materials Research, vol. 19, no. 1, pp. 195-201, 2016. DOI: https://doi.org/10.1590/1980-5373-MR-2015-0453
[19] M. Kaya , M. Aslan , O. Güler and Ü. Alver , "effect of fibre content on the mechanical properties of basalt fibre reinforced polylactic acid (pla) composites", Textile and Apparel, vol. 28, no. 1, pp. 66-71, Mar. 2018
[20] R. Mazur, G. Cândido, M. Rezende and E. Botelho, "Accelerated aging effects on carbon fiber PEKK composites manufactured by hot compression molding", Journal of Thermoplastic Composite Materials, vol. 29, no. 10, pp. 1429-1442, 2016. DOI: https://doi.org/10.1177/0892705714564283
[21] N. Cogswell, "Thermoplastic aromatic polymer composites," Int. Mater. Rev., 1st ed., vol. 39, no. 3, pp. 124-124, 1994. DOI: https://doi.org/10.1179/imr.1994.39.3.124
[22] Hexcel Corporation, hexcel, [On line]. Available: https://www.hexcel.com/Resources/DataSheets/Reinforcements/Woven-Reinforcements [Last access: 25 06 2020].
[23] E. Akca and A. Gursel, "A Review on the Matrix Toughness of Thermoplastic Materials," Period. Eng. Nat. Sci., vol. 3, no. 2, pp. 1-9, 2015. DOI: https://doi.org/10.21533/pen.v3i2.52
[24] F. Campbell, Manufacturing Processes for Advanced Composites, Elsevier, 2004
[25] M. Sanjay and B. Yogesha, "Studies on hybridization effect of jute/kenaf/E-glass woven fabric epoxy composites for potential applications: Effect of laminate stacking sequences," J. Ind. Text., vol. 47, no. 7, pp. 1830-1848, 2017. DOI: https://doi.org/10.1177/1528083717710713
[26] K. Sabeel Ahmed and S. Vijayarangan, "Tensile, flexural and interlaminar shear properties of woven jute and jute-glass fabric reinforced polyester composites," J. Mater. Process. Technol., vol. 207, pp. 330-335, 2008. DOI: https://doi.org/10.1016/j.jmatprotec.2008.06.038
[27] ASTM, Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials, 2007.
[28] ASTM, Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, 2017.
[29] ASTM, Standard Specification and Test Methods for Metallic Medical Bone Screws, West Conshohocken: ASTM Int, 2017.
[30] L. Chunrui, X. Nou, Z. Ting., Z. Xin, L. Hanxiong, L. Xue, L. Xiao and Z. Dongxing, "The Optimization of Process Parameters and Characterization of High-Performance CF/PEEK Composites Prepared by Flexible CF/PEEK Plain Weave Fabrics," Polymers, vol. 11, no. 53, p. 16, 2018. DOI: https://doi.org/10.3390/polym11010053
[31] H. Elwathing, G. Dengteng, Y. Lili, Z. Jianfeng and L. Mingxia, Y. Muhuo and Z. Shu, "Highly boosting the interlaminar shear strength of CF/PEEK composites via introduction of PEKK onto activated CF," Compos Part A-Appl S, vol. 112, pp. 155-160, 2018. DOI: https://doi.org/10.1016/j.compositesa.2018.05.029
[32] G. Shang-Lin and K. Jang-Kyo, "Cooling rate influences in carbon fiber/PEEK composites. Part 1. Crystallinity and interface adhesion," Compos Part A-Appl S, vol. 31, pp. 517-3530, 2000. DOI: https://doi.org/10.1016/S1359-835X(00)00009-9
[33] M. Sharma, J. Bijwe and P. Mitschang, "Wear performance of PEEK-carbon fabric composites with strengthened fiber-matrix interface," Wear, vol. 271, pp. 2061-2268, 2011. DOI: https://doi.org/10.1016/j.wear.2010.11.055
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Scientia et Technica
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Copyrights
The journal is free open access. The papers are published under the Creative Commons Attribution / Attribution-NonCommercial-NoDerivatives 4.0 International - CC BY-NC-ND 4.0 license. For this reason, the author or authors of a manuscript accepted for publication will yield all the economic rights to the Universidad Tecnológica of Pereira free of charge, taking into account the following:
In the event that the submitted manuscript is accepted for publication, the authors must grant permission to the journal, in unlimited time, to reproduce, to edit, distribute, exhibit and publish anywhere, either by means printed, electronic, databases, repositories, optical discs, Internet or any other required medium. In all cases, the journal preserves the obligation to respect, the moral rights of the authors, contained in article 30 of Law 23 of 1982 of the Government Colombian.
The transferors using ASSIGNMENT OF PATRIMONIAL RIGHTS letter declare that all the material that is part of the article is entirely free of copyright. Therefore, the authors are responsible for any litigation or related claim to intellectual property rights. They exonerate of all responsibility to the Universidad Tecnológica of Pereira (publishing entity) and the Scientia et Technica journal. Likewise, the authors accept that the work presented will be distributed in free open access, safeguarding copyright under the Creative Commons Attribution / Recognition-NonCommercial-NoDerivatives 4.0 International - https://creativecommons.org/licenses/by-nc-nd/4.0/deed.es license.